User Manual () Upgrade Instructions; 07/01/15; Download; Release Notes. Datasheet (). Datasheet () Upgrade Instructions; 08/31/15; Download. Don’t forget about our other Dlink DSLB info that you might be interested in. Login to Dlink DSLB Router ยท Change your Dlink DSLB IP Address. 5) The power light will first go red and the DSL light will flash. The DSL B comes with a lot of Manual Setup tick box and click the Setup Wizard button.

Author: Meztill Shaktizragore
Country: Suriname
Language: English (Spanish)
Genre: History
Published (Last): 12 July 2005
Pages: 407
PDF File Size: 2.54 Mb
ePub File Size: 1.6 Mb
ISBN: 155-8-88680-615-4
Downloads: 6258
Price: Free* [*Free Regsitration Required]
Uploader: Gubar

Strictly adhering to the IEEE nanual, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. Wan Interface Information The WAN Info page displays the status and mamual connect or disconnect button, depending on the selected connection mode. If wireless security is used, the wireless workstations must be properly configured for the security settings used.

Page 55 Import your existing certificate by pasting the dso-2640b content into the Certificate field dsl–2640b paste the private key into the Private Key del-2640b. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Got it, continue to print. Click Apply to apply the settings. By default, the system enables QoS and sets a default DSCP mark to automatically mark incoming traffic without reference to particular classifier.


All devices in your wireless network must use the same channel in order to work correctly. To verify your IP address, please follow the steps below. Wireless adsl2 plus router with ethernet wan support 38 pages. Click on the Add button to add outgoing filter settings. Don’t show me this message again. You can select it from the drop-down list. The firewall is used ds-l2640b block document transmissions between the Internet and your PC.

Click Security to proceed to the wireless security section. Update Settings Restore Default Settings will delete all current settings and restore the router to factory default settings. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety 90 days, whichever is longer, and is subject to the same limitations and exclusions. Enter the hostname and the interface that you are using. Troubleshooting Troubleshooting This chapter provides solutions to problems that might occur during the installation and operation of the DSLB.

Click Import Certificate and the following page appears.

Dlink DSL-2640B User Manual

By pressing ‘print’ button you will print only current page. Page 83 Lower integer values for precedence imply higher priority for this queue relative to others. Click Apply to save. Page 99 The MAC address appears listed in the table below. Web Configuration Click the Tone Selection button to modify the upstream and downstream tones. The interface that the packets pass through on the modem.


fsl-2640b Network re-auth interval is the time in which another key needs to be dynamically issued. All the adapters must be in Ad-Hoc mode to communicate. Click Apply to save any changes. Simple Network Management Protocol A protocol used for network management and monitoring network devices. Route Info The Route Info section displays route information showing the IP addresses of the destination, dsl2640b, and subnet mask as well as other route information. Page 43 Click Next, and the right page appears.


Page of Go. Enabled scan only those bridges whose Address: Manuql add another filter click Add. In this page, select a preferred WAN interface as the system default gateway. Security Network re-auth interval is the time in which another key needs to be dynamically issued.

Enter a MAC address of a computer on your network and click Apply.

SSID field and have selected your country from the drop-down list. Click Add to add the static routing. Enable or disable QoS.

After proper configuration, the right page appears. Page 71 Click Apply to save and activate the filter.

However, some IP traffic can be accepted by setting up filters. Test If a test displays a fail status, click Tests at the bottom of this page to make sure the fail status is consistent.

MAC addresses appear in these fields will be granted access.