ASTM D is a standard test method for vapor pressure of petroleum products. Find out more on ASTM D and their application and eralytics products. Lab Instruments · Application · Brand · Industry · Measurement · Method · ASTM · ASTM D36 · ASTM D56 · ASTM D86 · ASTM D92 · ASTM D93 · ASTM D Due to the increased use of ethanol in fuel the measurement of the Reid vapour pressure (RVP) is replaced by ASTM D in the EPA “Tier 3.
|Published (Last):||21 August 2007|
|PDF File Size:||20.51 Mb|
|ePub File Size:||20.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
New FM approved liquid analyser system is safe for h For the reproducibility this value even increases to 92 kPa. Regulatory changes and increasing safety concerns in recent years led to extensive adjustments in process and laboratory vapour pressure testing.
The calculated DVPE very closely approximates the dry vapor pressure that would be obtained on the same material when tested by Test Method D The results indicated that the repeatability limits of these samples are with in the published repeatability of this test method. The pressure is automatically measured at one minute intervals, until three readings are within 0.
Vapour Pressure Testing of Gasoline and Crude Oil – Regulatory Changes and Resulting Possibilities
This shows that a small loss of volatile content happened during sampling. Make your daily measuring routine a piece of cake: Link to Active This link will always route to the current Active version of the standard. Due to transport and storage some of the light ends possibly were lost before the measurement, thus lowering the resulting vapour pressure, compared to literature values. Work Item s – proposed revisions of this standard.
PAC-Lab Instruments-ASTM D
These steps are necessary for reproducible measurements. The valves utilise solvent resistant Kalrez seals.
For specific safety warning statements, see 7.
The ILS conducted in,and to determine the precision statements in Test Method D did not include any crude oil in the sample sets. The precision and bias statements for hazy samples have not been determined see Note Test Method Das well as IPhave been shown to be suitable for vapor pressure measurements of crude oils.
No account is made for dissolved water in the sample. Test Method D, as well as IPhave been shown to be suitable for vapor pressure measurements of crude oils. Additionally the triple expansion of ASTM D eliminates the influence caused by different air saturation levels of gasoline during the process measurements. The precision and bias statements for hazy samples have not been determined see Note With the piston based ASTM D it is possible to perform high quality measurements according to the standard, but again the sample preparation as described in the standard cannot be done correctly.
The vapour to liquid ratio is 4: Standard test method for vapor pressure of petroleum products mini method.
ASTM D – 18 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
The process monitoring of the vapour pressure during blending is aastm of performing trustfully measurements without the need of ongoing sampling for laboratory measurement. Note Samples can also be tested at other vapor-to-liquid ratios, temperatures, and pressures, but the precision and bias statements need not apply.
The gasoline measurements were performed using a typical Austrian gasoline blend.
Use Caution when handling mercury and mercury-containing products. Please see details here. How To Specify a Spectrometer. By accepting cookies, you can use this website with the full range of functions and optimize your browsing experience. These may be printed via the integral RS port and optional Data Printer What is the Difference between Flash Point and Fully evacuated chamber technology guarantees that the sample is tested under a full vacuum, as required by the “Mini” test methods.
Historical Version s – view previous versions of standard. The online and laboratory vapour adtm measurements of gasoline were performed at It incorporates a pressure sensor and is used to create the vacuum above the sample to determine the vapour pressure.
Dec 22 Read Jul 17 Read Also EN can be considered as an equivalent to this method. No account is made for dissolved water in the sample.
All valve operations are automated including sample draining also chamber venting and purging. Link to Active This link will always route to the current Active version of the standard. Inside the chamber, the test specimen is allowed to reach thermal equilibrium at the test temperature of The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law.
Setavap 2 Vapour Pressure Tester Part Number The Setavap 2 is used for the measurement of gasoline, solvents, light crude oils, and similar products, using the “Mini” method. Developments for crude oil measurements according to the advanced standard ASTM D as well as recent Tier 3 regulatory changes for vapour pressure testing of gasoline lead to changes that for the first time allow using the same measurement principle for process as well as laboratory measurements.
Link to Active This link will always route to the current Active version of the standard.