ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Country:||Republic of Macedonia|
|Published (Last):||17 December 2015|
|PDF File Size:||19.8 Mb|
|ePub File Size:||13.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool.
Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Type L LN If filler metal is required, Asttm is normally used.
The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Find out what NKS can a6666-10 for you. Only annealed conditions of grades speci? The noncontrolling factor normally will exceed considerably the speci? C Annealed material that naturally meets mechanical properties may be applied. Depending on the work hardening a66-10 of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the aatm.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. HRC typical L Ann 25 min. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides.
and L Stainless Steel – NKS
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. HardC Elongation in 2 in.
A number in parentheses indicates the year of last reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?
Originally approved in Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
However, in the case of dispute, tests shall be made by pressure.
The values given in parentheses are for information only. Rockwell B 95 95 The choice of test method for materials in conditions other than annealed shall be at the option of the seller. Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications. This standard has been approved for use by agencies of the Department of Defense. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully astn the part.
Last previous edition approved in as A — One bend test shall be made from one end of each coil.
In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. Asttm you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. D PSS means plate, strip, sheet. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Types and L cannot be hardened by thermal treatment. In case of dispute, the offset method of determining yield strength shall be used.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Number of Tests 8. A — 10 Standard Speci? These alloys represent an excellent combination of corrosion resistance and fabricability.